FastelFilm 230110 Heat Activated EVA Adhesive Film
FastelFilm 230110 can be used in applications where substrates can manage the higher heating temperature but require a higher continuous operating temperature. Through its higher operating temperature, it can be considered for more robust electronics, industrial, automotive or medical device/diagnostic applications. FastelFilm 230110 can be utilized as an adhesive interface bonding 2 substrates together or used as an interface perimeter sealing gasket.
As a dry-to-the-touch adhesive film, FastelFilm 230110 can be die cut to match a wide range of mounting and sealing applications areas. Once the adhesive pad is heated to or past its melt point temperature and cooled, the adhesive is set.
- Melt point temperature: 110C (mid-high melt design)
- Maximum continuous operating temperature: 80C
- EVA thermoplastic adhesive (ethylene vinyl acetate)
- Non-thermoset adhesive system (reworkable)
- Inert thermoplastic formulation | solvent free
- Bond flat and non-flat surfaces
- Dry film at room temperature (standard)
- Ideal for bonding heat sensitive substrates or reagents
- Free standing film available in a range of thicknesses
- 100% substrate surface coating available (films and foils)
- Discrete substrate placement capability
- Drop-in-place dry pad installation | clean adhesive assembly
- Optional release liner backings (PET film or paper)
- Optional liner release values (EZ to high release values)
- Available in rolls, sheets or die cuts
- Melt point: 230F | 110C (full liquid state)
- Continuous operating temperature: -30C to 80C (post bonding)
- Chemistry: EVA thermoplastic (non-thermoset)
- RoHS | REACH | Halogen Free Compliant
Standard Cross Section
Standard Film Thickness
- 0.038mm - 0.0015"
- 0.08mm - 0.003"
- 0.13mm - 0.005"
- 0.25mm - 0.010"
- 0.38mm - 0.015"
- 0.51mm - 0.020"
- 0.76mm - 0.030"
- Custom film thickness available
- Dry film surface (standard)
- LT (low tack repositionable - 0.013mm microsphere PSA lamination on one side of FastelFilm)
- Differential (barrier substrate film with FastelFilm one side and high strength pressure sensitive adhesive other side)
- See FastelFilm HPB versions for tack films without the use of lamination.
Release Liner Types
- White paper release liner
- Clear PET (polyester) release liner (multiple thicknesses and adhesive film release characteristics available depending on installation requirement)
- Release liner printing available (2 color)
- Master rolls
- Custom and Narrow slit rolls
- Die cut individuals
- Multiple die cuts per sheet
- Die cut continuous reels
- Laser cut (precision tolerance)
Coating & Adhesive Color
- Free standing film (standard)
- 100% substrate surface coating
- Discrete adhesive placement on substrate
- Translucent yellow (up to 0.13mm)
- Opaque yellow (0.18mm and up)
- Custom coloring available
- Aluminum foil
- Copper foil
- Stainless steel foil
- Polyimide film
- Polyester (PET) film
- Polypropylene film
- Customer defined substrate
DOE Testing (design of experiment)
Preparation | Installation Guidelines
CORONA TREATED SURFACES Corona treated surface modification may be a benefit depending on substrate material type. Customer testing required.TEXTURED SURFACES Textured surface may be a benefit in order to create more surface area depending on substrate type. Customer testing required.ADHESION PROMOTERS It is important for customers to determine compatability of adhesive promoter treatment.
Full Bond Heating Temp
No set heating time required. Dependent on thermal conductivity of substrates and heating devices. Minimum melt point must be acheived. No complex ramp up and ramp down patterns required unless other materials require this during the heating process.
Cooling (set) Time
Adhesive should be allowed to adequately cool below its melt point before applying stress. It is recommended (not required) to maintain pressure during cooling to promote surface contact during this process. Forced direct air systems okay to accelerate cooling.
Re-Work or Clean Up
Click here to learn more about our recommended heating equipment partners.